Bonjour,

Je reviens vers vous après une énième installation de mon serveur. (Petite précision : je suis débutant en système Linux ... ne nage un peu)

Ma dernière installation :
- Rutorrent avec 4 user en suivant ce tuto : https://mondedie.fr/d/5302
- Seedbox-manager en suivant ce tuto : https://mondedie.fr/d/5394
- RuFy en suivant ce tuto : https://mondedie.fr/d/8018
- Tardistart en suivant ce tuto : https://mondedie.fr/d/8067

Jusque ici tout fonctionnait correctement.

Ensuite, hier soir j'ai installé Plex en suivant ce tuto : https://mondedie.fr/d/5732
J'ai tout suivi à la lettre, fait la configuration comme expliqué dans le tuto. Tout avait l'air de fonctionner. J'avais accès a mon rutorrent, pouvais lire mes vidéos avec plex.
Ce matin je me connecte à mon rutorrent, je reçois une erreur me disant qu'il est impossible d’accéder à rtorrent. Seedbox-manager m'envoie sur une page m’expliquant comment l'installer et le configurer.

Je me connecte en ssh et lance un "service nginx restart".
Je reçois l'erreur :
Job for nginx.service failed. See 'systemctl status nginx.service' and 'journalctl -xn' for details.
systemctl status nginx.service :
root@ns398013:~# systemctl status nginx.service
● nginx.service - A high performance web server and a reverse proxy server
   Loaded: loaded (/lib/systemd/system/nginx.service; enabled)
   Active: failed (Result: exit-code) since mer. 2016-09-28 09:17:20 CEST; 24min ago
     Docs: man:nginx(8)
  Process: 11837 ExecStop=/sbin/start-stop-daemon --quiet --stop --retry QUIT/5 --pidfile /run/nginx.pid (code=exited, status=0/SUCCESS)
  Process: 12274 ExecStartPre=/usr/sbin/nginx -t -q -g daemon on; master_process on; (code=exited, status=1/FAILURE)
 Main PID: 31008 (code=exited, status=0/SUCCESS)

sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: Starting A high performance web server and a reverse pr...r...
sept. 28 09:17:20 ns398013.ip-151-80-41.eu nginx[12274]: nginx: [alert] could not open error log file: open() "...em)
sept. 28 09:17:20 ns398013.ip-151-80-41.eu nginx[12274]: 2016/09/28 09:17:20 [emerg] 12274#12274: open() "/var/...em)
sept. 28 09:17:20 ns398013.ip-151-80-41.eu nginx[12274]: nginx: configuration file /etc/nginx/nginx.conf test failed
sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: nginx.service: control process exited, code=exited status=1
sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: Failed to start A high performance web server and a rev...ver.
sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: Unit nginx.service entered failed state.
Hint: Some lines were ellipsized, use -l to show in full.
journalctl -xn :
root@ns398013:~# systemctl status nginx.service
● nginx.service - A high performance web server and a reverse proxy server
   Loaded: loaded (/lib/systemd/system/nginx.service; enabled)
   Active: failed (Result: exit-code) since mer. 2016-09-28 09:17:20 CEST; 24min ago
     Docs: man:nginx(8)
  Process: 11837 ExecStop=/sbin/start-stop-daemon --quiet --stop --retry QUIT/5 --pidfile /run/nginx.pid (code=exited, status=0/SUCCESS)
  Process: 12274 ExecStartPre=/usr/sbin/nginx -t -q -g daemon on; master_process on; (code=exited, status=1/FAILURE)
 Main PID: 31008 (code=exited, status=0/SUCCESS)

sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: Starting A high performance web server and a reverse pr...r...
sept. 28 09:17:20 ns398013.ip-151-80-41.eu nginx[12274]: nginx: [alert] could not open error log file: open() "...em)
sept. 28 09:17:20 ns398013.ip-151-80-41.eu nginx[12274]: 2016/09/28 09:17:20 [emerg] 12274#12274: open() "/var/...em)
sept. 28 09:17:20 ns398013.ip-151-80-41.eu nginx[12274]: nginx: configuration file /etc/nginx/nginx.conf test failed
sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: nginx.service: control process exited, code=exited status=1
sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: Failed to start A high performance web server and a rev...ver.
sept. 28 09:17:20 ns398013.ip-151-80-41.eu systemd[1]: Unit nginx.service entered failed state.
Hint: Some lines were ellipsized, use -l to show in full.
root@ns398013:~# journalctl -xn
-- Logs begin at sam. 2016-09-24 14:22:50 CEST, end at mer. 2016-09-28 09:43:01 CEST. --
sept. 28 09:35:01 ns398013.ip-151-80-41.eu CRON[12996]: (CRON) error (create tmpfile)
sept. 28 09:36:01 ns398013.ip-151-80-41.eu CRON[13035]: (CRON) error (create tmpfile)
sept. 28 09:37:01 ns398013.ip-151-80-41.eu CRON[13072]: (CRON) error (create tmpfile)
sept. 28 09:38:01 ns398013.ip-151-80-41.eu CRON[13111]: (CRON) error (create tmpfile)
sept. 28 09:39:01 ns398013.ip-151-80-41.eu CRON[13150]: (CRON) error (create tmpfile)
sept. 28 09:39:01 ns398013.ip-151-80-41.eu CRON[13151]: (CRON) error (create tmpfile)
sept. 28 09:40:01 ns398013.ip-151-80-41.eu CRON[13203]: (CRON) error (create tmpfile)
sept. 28 09:41:01 ns398013.ip-151-80-41.eu CRON[13243]: (CRON) error (create tmpfile)
sept. 28 09:42:01 ns398013.ip-151-80-41.eu CRON[13283]: (CRON) error (create tmpfile)
sept. 28 09:43:01 ns398013.ip-151-80-41.eu CRON[13322]: (CRON) error (create tmpfile)
Tout cela ne me parle pas trop.

Pour info mon fichier rutorrent.conf :
upstream rufy_server {
  server unix:/var/www/RuFy/run/gunicorn.sock fail_timeout=0;
}

server {
    listen 80 default_server;
    listen 443 default_server ssl;
    server_name _;

    charset utf-8;
    index index.html index.php;
    client_max_body_size 10M;

    ssl_certificate /etc/nginx/ssl/server.crt;
    ssl_certificate_key /etc/nginx/ssl/server.key;
    ssl_dhparam /etc/nginx/ssl/dhparam.pem;

    access_log /var/log/nginx/rutorrent-access.log combined;
    error_log /var/log/nginx/rutorrent-error.log error;

    error_page 500 502 503 504 /50x.html;
    location = /50x.html { root /usr/share/nginx/html; }

    auth_basic "seedbox";
    auth_basic_user_file "/etc/nginx/passwd/rutorrent_passwd";

    location = /favicon.ico {
        access_log off;
        log_not_found off;
    }

    ## début config rutorrent ##

    location ^~ /rutorrent {
	root /var/www;
	include /etc/nginx/conf.d/php.conf;
	include /etc/nginx/conf.d/cache.conf;

	location ~ /\.svn {
		deny all;
	}

	location ~ /\.ht {
		deny all;
	}
    }

    location ^~ /rutorrent/conf/ {
	deny all;
    }

    location ^~ /rutorrent/share/ {
	deny all;
    }

    location /KHOBAL {
        include scgi_params;
        scgi_pass 127.0.0.1:5001;
        auth_basic "seedbox";
        auth_basic_user_file "/etc/nginx/passwd/rutorrent_passwd_khobal";
    }

    location /WOLVIE {
        include scgi_params;
        scgi_pass 127.0.0.1:5002;
        auth_basic "seedbox";
        auth_basic_user_file "/etc/nginx/passwd/rutorrent_passwd_wolvie";
    }

    location /MIKLNET {
        include scgi_params;
        scgi_pass 127.0.0.1:5003;
        auth_basic "seedbox";
        auth_basic_user_file "/etc/nginx/passwd/rutorrent_passwd_miklnet";
    }

    location /TOUFFIC {
        include scgi_params;
        scgi_pass 127.0.0.1:5004;
        auth_basic "seedbox";
        auth_basic_user_file "/etc/nginx/passwd/rutorrent_passwd_touffic";
    }

    ## fin config rutorrent ##

    ## début config seedbox-manager ##

    location ^~ /seedbox-manager {
	alias /var/www/seedbox-manager/public;
        include /etc/nginx/conf.d/php-manager.conf;
	include /etc/nginx/conf.d/cache.conf;
    }

    ## fin config seedbox-manager ##

    ## début config rufy ##

    location ^~/rufy/static {
        satisfy any;
        allow all;
        alias /var/www/RuFy/static/;
    }

    location ^~/rufy {
        satisfy any;
        allow all;

        proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;
        proxy_set_header Host $http_host;
        proxy_redirect off;
        if (!-f $request_filename) {
            proxy_pass http://127.0.0.1:8000;
            break;
        }
    }

    ## fin config rufy ##

    ## début config tardistart ##

        location ^~/{
                root /var/www/tardistart;
                include /etc/nginx/conf.d/php.conf;
                include /etc/nginx/conf.d/cache.conf;
                satisfy any;
                allow all;

                location ~ admin {
                        auth_basic "TARDIStart Admin Page";
                        auth_basic_user_file "/etc/nginx/passwd/rutorrent_passwd_khobal";
                        deny all;
                }
        }

    ## fin config tardistart ##


}
Besoin d'autre info ?
Je suis preneur de toutes idées (ou solution 😀)

Merci d'avance.
Tu peux nous copier/coller le message complet que remonte nginx lors du lancement ?
Agrandit ta fenêtre
Bonjour , peut tu poster ton fichier
 /etc/nginx/nginx.conf 
Le problème vient surement d'ici
Salut, que te renvoie la commande suivante ?
nginx -t
Jedediah wrote:Tu peux nous copier/coller le message complet que remonte nginx lors du lancement ?
Agrandit ta fenêtre smile
C'est a dire ? j'ai rien de plus en agrandissant ma fenetre.
majaxx wrote:Bonjour , peut tu poster ton fichier
/etc/nginx/nginx.conf
Le problème vient surement d'ici
user www-data;
worker_processes auto;
pid /var/run/nginx.pid;

events {
    worker_connections 1024;
    use epoll; # gestionnaire d'évènements epoll (kernel 2.6+)
}

http {
    include /etc/nginx/mime.types;
    default_type  application/octet-stream;

    access_log /var/log/nginx/access.log combined;
    error_log /var/log/nginx/error.log error;

    sendfile on;
    keepalive_timeout 15;
    keepalive_disable msie6;
    keepalive_requests 100;
    tcp_nopush on;
    tcp_nodelay off;
    server_tokens off;

    gzip on;
    gzip_comp_level 5;
    gzip_min_length 512;
    gzip_buffers 4 8k;
    gzip_proxied any;
    gzip_vary on;
    gzip_disable "msie6";
    gzip_types
        text/css
        text/javascript
        text/xml
        text/plain
        text/x-component
        application/javascript
        application/x-javascript
        application/json
        application/xml
        application/rss+xml
        application/vnd.ms-fontobject
        font/truetype
        font/opentype
        image/svg+xml;

    include /etc/nginx/sites-enabled/*.conf;
}
matt wrote:Salut, que te renvoie la commande suivante ?
nginx -t
root@ns398013:~# nginx -t
nginx: [alert] could not open error log file: open() "/var/log/nginx/error.log" failed (30: Read-only file system)
nginx: the configuration file /etc/nginx/nginx.conf syntax is ok
2016/09/28 10:19:22 [emerg] 14982#14982: open() "/var/log/nginx/access.log" failed (30: Read-only file system)
nginx: configuration file /etc/nginx/nginx.conf test failed
Un petit
chmod -R 755 /var/log/nginx
devrait corriger ton souci
root@ns398013:~# chmod -R 755 /var/log/nginx
chmod: modification des droits de « /var/log/nginx »: Système de fichiers accessible en lecture seulement
chmod: modification des droits de « /var/log/nginx/rutorrent-access.log »: Système de fichiers accessible en lecture seulement
chmod: modification des droits de « /var/log/nginx/error.log »: Système de fichiers accessible en lecture seulement
chmod: modification des droits de « /var/log/nginx/rutorrent-error.log.1 »: Système de fichiers accessible en lecture seulement
chmod: modification des droits de « /var/log/nginx/rutorrent-access.log.1 »: Système de fichiers accessible en lecture seulement
chmod: modification des droits de « /var/log/nginx/error.log.1 »: Système de fichiers accessible en lecture seulement
chmod: modification des droits de « /var/log/nginx/rutorrent-error.log »: Système de fichiers accessible en lecture seulement
chmod: modification des droits de « /var/log/nginx/access.log »: Système de fichiers accessible en lecture seulement
root@ns398013:~# service nginx restart
Job for nginx.service failed. See 'systemctl status nginx.service' and 'journalctl -xn' for details.
Tu peux nous faire un
ls -l /var/log
et nous coller le résultat ?

Ainsi qu'un
df -h
root@ns398013:~# ls -l /var/log
total 2820
-rw-r--r-- 1 root     root    7991 sept. 26 09:32 alternatives.log
drwxr-xr-x 2 root     root    4096 nov.   6  2014 apt
-rw-r--r-- 1 root     root   14374 sept. 27 19:30 aptitude
-rw-r----- 1 root     adm  1526850 sept. 28 06:35 auth.log
-rw------- 1 root     utmp  381312 sept. 28 04:33 btmp
-rw-r----- 1 root     adm   207839 sept. 28 06:23 daemon.log
-rw-r----- 1 root     adm    21416 sept. 28 06:14 debug
-rw-r----- 1 root     adm        0 nov.   6  2014 dmesg
-rw-r--r-- 1 root     root  219413 sept. 27 19:35 dpkg.log
-rw-r--r-- 1 root     root   32128 sept. 27 19:35 faillog
drwxr-xr-x 2 root     root    4096 janv. 24  2016 fsck
-rw-r----- 1 root     adm    73724 sept. 28 06:14 kern.log
-rw-rw-r-- 1 root     utmp  293168 sept. 27 21:44 lastlog
-rw-r----- 1 root     adm    59297 sept. 28 06:26 messages
drwxr-x--- 2 www-data adm     4096 sept. 28 06:25 nginx
-rw------- 1 root     root    1035 sept. 26 09:45 php7.0-fpm.log
drwxr-xr-x 2 root     root    4096 sept. 27 16:41 supervisor
-rw-r----- 1 root     adm     1263 sept. 28 06:36 syslog
-rw-r----- 1 root     adm   216499 sept. 28 06:25 syslog.1
-rw-r----- 1 root     adm    15267 sept. 27 06:25 syslog.2.gz
-rw-r----- 1 root     adm    40107 sept. 26 06:25 syslog.3.gz
-rw-rw-r-- 1 root     utmp   17664 sept. 27 21:50 wtmp
root@ns398013:~# df -h
Sys. de fichiers Taille Utilisé Dispo Uti% Monté sur
/dev/root           15G    2,5G   12G  18% /
devtmpfs           7,8G       0  7,8G   0% /dev
tmpfs              7,8G    4,0K  7,8G   1% /dev/shm
tmpfs              7,8G     26M  7,8G   1% /run
tmpfs              5,0M       0  5,0M   0% /run/lock
tmpfs              7,8G       0  7,8G   0% /sys/fs/cgroup
/dev/sda2          189M     23M  153M  13% /boot
/dev/sda5          1,8T    209G  1,5T  13% /home
Salut
le "Read-only file system" peut être arrivé avec un soucis de disk ou de point de montage, il bloque tout par sécurité.
Tu devrais faire un test smart pour voir si ça te sort un problème (moi ça me parlera pas beaucoup mais...).
smartctl -a /dev/sda
si il ne connait pas smartctl:
apt-get install smartmontools
la ligne SMART Error Log peut être parlante
Ex.
+1 exrat

Ton filesystem semble être en lecture seul.
J'ai eu un soucis similaire par le passé sur un ordinateur sous linux,

Pour info, j'avais démarrer sous LiveCD et exécuter un fsck sur la partition incriminer, j'avais des nodes en défaut, et j'ai pu remettre le disque en lecture écriture.

Dans ton cas pas de possibilité de LiveCD, mais regarde si tu as un mode rescue de proposer ou ouvre un ticket chez ton hébergeur pour voir si ils peuvent pas le faire eux.
En effet. Il y a l'air d'y avoir des erreurs SMART.

root@ns398013:~# smartctl -a /dev/sda
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.14.32-xxxx-grs-ipv6-64] (local bui                                                                                        ld)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 3.5" HDD DT01ACA...
Device Model:     TOSHIBA DT01ACA200
Serial Number:    333PT3XKS
LU WWN Device Id: 5 000039 ff3c9e65c
Firmware Version: MX4OABB0
User Capacity:    2 000 398 934 016 bytes [2,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Thu Sep 29 10:15:06 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x84) Offline data collection activity
                                        was suspended by an interrupting command                                                                                         from host.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (15109) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off supp                                                                                        ort.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 252) minutes.
SCT capabilities:              (0x003d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_                                                                                        FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   091   091   016    Pre-fail  Always       -                                                                                               1703969
  2 Throughput_Performance  0x0005   139   139   054    Pre-fail  Offline      -                                                                                               72
  3 Spin_Up_Time            0x0007   133   133   024    Pre-fail  Always       -                                                                                               286 (Average 285)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -                                                                                               61
  5 Reallocated_Sector_Ct   0x0033   001   001   005    Pre-fail  Always   FAILI                                                                                        NG_NOW 1995
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -                                                                                               0
  8 Seek_Time_Performance   0x0005   124   124   020    Pre-fail  Offline      -                                                                                               33
  9 Power_On_Hours          0x0012   098   098   000    Old_age   Always       -                                                                                               14075
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -                                                                                               0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -                                                                                               61
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -                                                                                               69
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -                                                                                               69
194 Temperature_Celsius     0x0002   200   200   000    Old_age   Always       -                                                                                               30 (Min/Max 17/51)
196 Reallocated_Event_Count 0x0032   001   001   000    Old_age   Always       -                                                                                               2214
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -                                                                                               80
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -                                                                                               0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -                                                                                               0

SMART Error Log Version: 1
ATA Error Count: 76 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 76 occurred at disk power-on lifetime: 13958 hours (581 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle                                                                                        .

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 cf 56 00  Error: UNC at LBA = 0x0056cf08 = 5689096

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 a8 08 cf 56 40 00   2d+22:02:16.651  READ FPDMA QUEUED
  61 08 a0 28 41 ce 40 00   2d+22:02:16.444  WRITE FPDMA QUEUED
  61 10 98 18 41 ce 40 00   2d+22:02:16.425  WRITE FPDMA QUEUED
  ef 10 02 00 00 00 a0 00   2d+22:02:16.422  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 e0 00   2d+22:02:16.422  READ NATIVE MAX ADDRESS EXT [OBS-AC                                                                                        S-3]

Error 75 occurred at disk power-on lifetime: 13958 hours (581 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle                                                                                        .

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 cf 56 00  Error: WP at LBA = 0x0056cf08 = 5689096

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 10 90 18 41 ce 40 00   2d+22:02:15.653  WRITE FPDMA QUEUED
  60 08 88 08 cf 56 40 00   2d+22:02:12.584  READ FPDMA QUEUED
  61 08 80 10 41 ce 40 00   2d+22:02:01.720  WRITE FPDMA QUEUED
  61 50 78 c0 40 ce 40 00   2d+22:02:01.708  WRITE FPDMA QUEUED
  61 08 70 60 66 4a 40 00   2d+22:01:45.165  WRITE FPDMA QUEUED

Error 74 occurred at disk power-on lifetime: 13958 hours (581 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle                                                                                        .

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 cf 56 00  Error: WP at LBA = 0x0056cf08 = 5689096

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 08 80 c8 76 87 40 00   2d+22:01:07.251  WRITE FPDMA QUEUED
  61 08 78 f8 4a 86 40 00   2d+22:01:07.251  WRITE FPDMA QUEUED
  61 08 70 20 49 86 40 00   2d+22:01:07.251  WRITE FPDMA QUEUED
  61 08 68 00 49 86 40 00   2d+22:01:07.251  WRITE FPDMA QUEUED
  61 08 60 80 48 86 40 00   2d+22:01:07.251  WRITE FPDMA QUEUED

Error 73 occurred at disk power-on lifetime: 13958 hours (581 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle                                                                                        .

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 cf 56 00  Error: UNC at LBA = 0x0056cf08 = 5689096

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 40 08 cf 56 40 00   2d+22:01:02.317  READ FPDMA QUEUED
  61 08 38 30 40 ce 40 00   2d+22:01:02.258  WRITE FPDMA QUEUED
  61 50 30 e0 3f ce 40 00   2d+22:01:02.230  WRITE FPDMA QUEUED
  61 08 28 10 bf 8a 40 00   2d+22:01:02.230  WRITE FPDMA QUEUED
  61 08 20 d8 30 58 40 00   2d+22:01:02.230  WRITE FPDMA QUEUED

Error 72 occurred at disk power-on lifetime: 13958 hours (581 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle                                                                                        .

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 08 cf 56 00  Error: UNC at LBA = 0x0056cf08 = 5689096

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 08 20 08 cf 56 40 00   2d+21:59:56.097  READ FPDMA QUEUED
  61 08 18 38 3f ce 40 00   2d+21:59:55.892  WRITE FPDMA QUEUED
  61 08 10 b0 61 2f 40 00   2d+21:59:55.865  WRITE FPDMA QUEUED
  61 08 08 a8 61 2f 40 00   2d+21:59:55.865  WRITE FPDMA QUEUED
  61 28 00 10 3f ce 40 00   2d+21:59:55.865  WRITE FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA                                                                                        _of_first_error
# 1  Short offline       Completed without error       00%      3759         -
# 2  Short offline       Completed without error       00%      3757         -
# 3  Short offline       Completed without error       00%      3757         -
# 4  Short offline       Completed without error       00%      2783         -
# 5  Short offline       Completed without error       00%      2783         -
# 6  Short offline       Completed without error       00%      2775         -
# 7  Short offline       Completed without error       00%      2714         -
# 8  Short offline       Completed without error       00%      2698         -
# 9  Short offline       Completed without error       00%        47         -
#10  Short offline       Completed without error       00%        38         -
#11  Short offline       Completed without error       00%        38         -
#12  Short offline       Completed without error       00%         2         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
J'ouvre un ticket chez Kimsufi.Je vous tiens au courant.

Merci beaucoup pour l'aide
13 jours plus tard
Ils m'ont changés le disque (au bout de deux semaines).

Problème résolut merci pour les infos
Répondre…